| LP9802 - Emulex LightPulse
Single Channel 2GB/s Fibre PCI-X Host Bus Adapter The
LP9802 PCI-X host bus adapter offers a highly integrated 2Gbs Fibre
Channel HBA for use in servers based on either PCI or the latest PCI-X
expansion bus. The LP9802 delivers exceptional performance through
the use of an Emulex Pegasus ASIC, a 266MIPs onboard processor, an
embedded 1Gig/2Gig SERDES, and a high performance unified QDR SRAM.
The LP9802 features automatic topology detection and automatic
topology detection and automatic speed negotiation capability. These
capabilities allow complete compatibility with existing 1Gb/s Fibre
Channel SANs, while allowing seamless upgrades to higher speed 2Gb/s
SANs.
The features of this PCI-X based HBA provide the flexibility and
broad interoperability needed for complex, highly scalable SANs. The
LP9802 provides a combination of features, including fabric support
using F_Port and FL_Port connections, full-duplex data transfers,
high data integrity features, support for all Fibre Channel
topologies, and support for service classes 2 and 3.
The LP9802 also features sophisticated hardware that provides
superior performance in SANs and provides best in class server CPU
offload. This exclusive hardware delivers low latency and high
throughput in fabric, arbitrated loop and clustered environments.
Support for fiber optic cabling is provided through an embedded
small form factor (LC) optical interface.
Key Benefits:
* Superior quality and reliability ensures data availability
* The most efficient installation accelerates deployment and reduces
administration costs
* Maximum SAN performance increases scalability and user
satisfaction in large enterprise installations
* Robust interoperability simplifies deployment and upgrades of SAN
hardware and software
Key Features:
* Exceptional performance and full-duplex data throughput
* Simplified installation and configuration using common HBA drivers
and AutoPilot Installer®
* Efficient administration via HBAnyware® for HBAs anywhere in the
SAN
* Common driver model eases management and enables upgrades
independent of HBA firmware
*Full duplex 2Gb/s Fibre Channel delivering up to 400MB/s
*Automatic speed negotiation
*Automatic topology detection
*Full fabric support using F_Port and FL_port connections
*Onboard hardware context cache for superior fabric performance
*Support for multiple concurrent protocols (SCSI and IP)
*Full support for both FC service class 2 and 3
*Full fabric boot support in x86 and SPARC environments to multiple
LUNs
*Support for FC-Tape (FCP-2) devices
*66/100/133 MHz PCI-X 1.0a and PCI 2.2 compatibility
*End-to-end parity protection for high data integrity
*Buffered data architecture to support over 50km cabling at full
2Gb/s bandwidth
*Robust suite of software supporting Windows Server 2003, Windows
2000, *Windows NT, HP-UX, Linux, NetWare and Solaris
*Optical small form factor (LC) interface
Technical Specifications:
STANDARDS
*ANSI Fibre Channel FC-FS
*ANSI Fibre Channel FC-PH
*ANSI Fibre Channel FC-PI
*ANSI Fibre Channel FC-AL
*ANSI Fibre Channel FC-PLDA
*ANSI Fibre Channel FC-MI
*ANSI Fibre Channel FC-FLA
*PCI-X 1.0a
*PCI local bus revision 2.2 (see power requirements)
*Fibre Channel Class 2, 3
*PHP hot plug - hot swap
ARCHITECTURE
*Emulex Pegasus ASIC technology
*up to 133MHz PCI-X DMA
*2Gb/s or 1Gb/s FC Link
*2MB FLASH memory
*2MB QDR SRAM
SOFTWARE ENVIRONMENTS
*Windows Server 2003
*Windows 2000
*Windows NT
*HP-UX
*Linux
*NetWare
*Solaris
HARDWARE ENVIRONMENTS
*x86, SPARC and PowerPC PCI hardware platforms
*3.3V signaling, 5V tolerant
*32/64b 33/66MHz PCI
*66/100/133MHz PCI-X
*OPTICAL
*Data rates: 1.0625/2.125Gb/s
*Optics: short/long wave lasers
*Cable: 9/125μm single-mode fiber50/125μm multi-mode fiber62.5/125μm
multi-*mode fiber
*Connector: LC
*Distance: (1Gb/s)10K meters (32,800') 9/125 μm fiber500 meters
(1,640') *50/125 μm fiber300 meters (984') 62.5/125 μm fiber(2Gb/s)
10K meters *(32,800') 9/125 μm fiber300 meters (984') 50/125 μm
fiber150 meters (492') *62.5/125 μm fiber
POWER REQUIREMENTS
*Volts: +3.3 VDC (± 5%)
*Power: 7.7 watts @ 66MHz, 8.5 watts @ 133MHz (typ)
ENVIRONMENTAL CONDITIONS
*Operating temperature: 0° to 45°C (32° to 113°F)
*Airflow required: 100 lf/m
*Storage temperature: -40° to 70°C (-40° to 158°F)
*Relative humidity: 5% to 95% non-condensing
AGENCY APPROVALS
*Class 1 Laser Product per DHHS 21CFR (J) & EN60825
*UL recognized to UL 1950
*CUR recognized to CSA22.2, No. 950
*TUV certified to EN60950
*FCC rules, Part 15, Class A
*ICES–003, Class A
*EMC Directive 89/336/EEC (CE Mark) - EN55022, Class A - EN55024
*Australian EMC Framework (C–Tick Mark) - AS/NZS 3548, Class A
*VCCI, Class A
|